1. Willkommen im Forum! Registriere dich, um eigene Beiträge zu schreiben.

Walkera qr X350 pro v5.0.0 does not bind with DEVO10

Dieses Thema im Forum "X350 und X350 Pro" wurde erstellt von NSC, 21. Juli 2020.

  1. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    Hello everyone! I just received Walkera QR X350 Pro with DEVO 10 2.4GHz, 5.8GHz 600mW ImmersionRC camera boost and Q-2D Gimbal. Could anyone please help me get this bird in the air? I don`t know what is wrong with it but it does not bind with the DEVO`10. Which Protocol should I select on the RC to bind it to the Walkera? Any help is welcome, I don`t know anything about Walkera or DEVO. Thank you!
     

    Anhänge:

  2. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    Hello,welcome to the forum
    On the DEVO 10 you have to select DEVO as protocol
     
  3. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
  4. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    Quickstart english
    Modelfiles for Devo10
     

    Anhänge:

  5. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    This is in the TX.ini of DEVO10. Should I change it with the one that I downloaded from the Walkera fans? How to open .bin file to see what it has written on it? I am attaching the hardware.ini tx.ini and datalog.bin. I don`t see .bin file with name "X350 Pro Devo 10.bin" in my DEVO10. I am attaching the .rar , which contains all files from my DEVO10 too. Thank you!
     

    Anhänge:

  6. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    This file X350 Pro Devo 10.bin
    is copied onto the Devo.
    How that works, look at this.
    Walkera Update Anleitungen – Walkera Fans
    Your Devo is new without a model file and can't bond with the copter.
    Sorry, I only speak a little English and let it be
    Translator running.
     
  7. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
  8. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    Your English is great ! Do you want me to follow all steps from Walkera Update Instructions and install Dfuse USB Upgrade Tools 3? What is Walkera-FlyConfig-Drones-Assistant-Portable-1.0? Can I just copy/paste in my DEVO 10 all files from this .rar or this is not enough and I must follow all steps in Walkera Update Instruction via Dfuse USB Upgrade Tools 3? Thank you!
     

    Anhänge:

  9. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    What is Walkera-FlyConfig-Drones-Assistant-Portable-1.0?
    Not for 350Pro
    Do you want me to follow all steps from Walkera Update Instructions and install Dfuse USB Upgrade Tools 3?
    yes
     
  10. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    Download also 350 Pro manual english from here
     
  11. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    Great! After the update and reinstall of the firmware, DEVO10 wasnt able to bind to Walkera. So I removed the Fixed ID and finally they bound!! So happy. Now next question - I tried to enter calibration mode, by moving the two sticks down and inwards to the middle ( drone does not flash or anything at this point ), then I follow the 3 steps to spin the drone in the right directions, but there is no signal or green light flashing to show number of satellites. I tried to unlock the motors but nothing happen either. This is the DEVO 10 updated files. (I can see a solid red light in the drone and a flashing blue light. Should I open the shell and see what is inside?) Thank you!
     

    Anhänge:

  12. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    :)
    (I can see a solid red light in the drone and a flashing blue light
    This red light is receiver RX..ok
    the blue light is gps
    have you the manual ?
     
  13. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    You have to do the calibration under the open sky.
    It takes the GPS module a while to find satellites.
    This is the right green LED. At least 5 flashes
    The left green LED blinks until the binding, then it is permanently lit, if it blinks in flight, the battery is running low.
    Land immediately
     
  14. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
  15. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    I have no green lights on or flashing after binding. just the solid red and flashing blue I can see in the drone.
     
  16. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    Is your lipo loaded from the copter?
    And the one in Devo's too?
    How can you tell if the Copter and Devo have bonded?
     
  17. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    I think I still have about 11V in the DEVO and Drone. The left green flashes quickly then slowly and then goes off - that means the drone and RC are bounded. Then I move the two sticks down and middle but left green does not start flashing - which means I am not in calibration mode according to the manual - left green must flash very quickly and then goes off and the right green flash as many times as it has connected to satellites. Am I doing something wrong?
     
  18. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
    The lipo in the copter must be at least 3.7 volts per
    have a cell
    Move the two sticks down to the outside
     
  19. linux

    linux Walkera Wahnsinniger

    Beiträge:
    4.581
    Zustimmungen:
    581
    Ort:
    Bad Emstal
  20. NSC

    NSC Starker Walkerafan

    Beiträge:
    96
    Zustimmungen:
    1
    The drone battery has 12V the RC battery currently has 11.1V ( just measured them with multimeter). Nothing happens when I move the sticks as shown on this photo... No green lights flashing or sound from RC.
     
Die Seite wird geladen...
Ähnliche Themen - Forum Datum
Modifikation Walkera qr x350 pro Kompass Eigenbau Eigenbau und Komplett-Modifikationen 9. Sep. 2020
Walkera X350 Pro Akku X350 und X350 Pro 23. Mai 2020
Verkaufe Walkera QR X350-Z-10 ESC RC Zubehör 9. Dez. 2018
Problem Walkera qr x350 pro welches Ladegerät X350 und X350 Pro 17. Nov. 2018
Batterie für walkera x350 pro X350 und X350 Pro 28. Mai 2018